Gas Buildup Issues

Gas Buildup in Injection Molding

Gas buildup can lead to burning, splay, and other defects on molded parts. Nanoplas products can help keep your output defect-free and your run time up.

Common Cause:

Over Applying Mold Release

Over applying mold release to avoid sticking during a full production run can cause the mold release to build up and clog the vents.

Solution:

Mold Guard Rust Preventative Cut Out

Dri-Kote™

Quick drying Dri-Kote mold release spray uses an innovative spray pattern to lay down a thin coat. This helps prevent mold release buildup, especially in the problem areas of a mold, so you don’t get gas build up. Dri-Kote works for most injection molding needs. 

Request a Free Sample

Solution:

Mold Guard Rust Preventative Cut Out

Tuff-Kote™

Quick drying Tuff-Kote mold release spray uses an innovative spray pattern to lay down a thin coat. This helps prevent mold release buildup, especially in the problem areas of a mold, so you don’t get gas build up. Tuff-Kote is for difficult-to-release parts.

Request a Free Sample

Solution:

Mold Guard Rust Preventative Cut Out

A Nanoplas Coating

Especially ideal for plastic or rubber part release, Nanoplas coatings use nanotechnology to create a semi-permanent barrier on the mold’s surface. They have no impact on finished part dimension, don’t migrate to the part surface, and are non-toxic. Additionally, you apply them in-house and they cure in just a few hours.

Request a Free Sample

Common Cause:

Over Applying Rust Preventative

In some cases you may be dealing with rust preventative building up and clogging vents. It may be because your rust preventative is being over applied or is thick in nature. It could also be that your rust preventative is wet (as in not drying quickly enough), so it migrates throughout the mold. Applying a wet rust preventative to a hot mold will also create a tacky residue on mold surfaces.

Solution:

Mold Guard Rust Preventative Cut Out

Mold Guard™

Mold Guard is a truly dry rust preventative, so it won’t migrate or buildup when applied as directed. An adjustable fan tip gives better control over the volume dispensed. Plus, it can be molded through at start-up and creates little to no scrap.

Request a Free Sample

Solution:

Mold Guard Rust Preventative Cut Out

Mold Guard Green™

Mold Guard Green is a truly dry rust preventative, so it won’t migrate or buildup when applied as directed. An adjustable fan tip gives better control over the volume dispensed. Plus, it can be molded through at start-up and creates little to no scrap. Mold Guard Green has a green tint, so you can see where it’s been applied.

Request a Free Sample

Common Cause:

Poor Venting/Tool Design

Truly resolving this issue requires the tool or mold itself to be examined for proper vent depths, and addressed as needed. That being said, you’ll still need a cleaner to remove the excess gas buildup.

Solution:

Mold Guard Rust Preventative Cut Out

Zap-Ox™

Zap-Ox will remove gas build up in seconds, minimizing downtime. There is no other cleaner that can remove rust, oxidation, buildup, weld discoloration, and other stains as effectively and efficiently as Zap-Ox.

Request a Free Sample

Common Cause:

Molding Material

The type of material used in producing the product combined with poor venting within the tool can trap gasses, creating buildup. The long-term solution is pairing the material with the right mold/tool. To address the immediate issue of gas buildup, use a mold cleaner.

Solution:

Mold Guard Rust Preventative Cut Out

Zap-Ox™

Zap-Ox will remove gas build up in seconds, minimizing downtime. There is no other cleaner that can remove rust, oxidation, buildup, weld discoloration, and other stains as effectively and efficiently as Zap-Ox.

Request a Free Sample

See How Effectively Zap-Ox Cleans

Better Together

When used in tandem, Nanoplas products can help you significantly reduce costs, downtime, scrap, and more. Scientifically formulated, each product is individually effective, so when used together, they enhance mold performance significantly.

Zap-Ox Saves Hours of Tool Maintenance

See Case Study

Used Zap-Ox to clean gassing and burn marks at the end of fill. This saves hours of tool maintenance. Normally, you would have to pull the tool and stone polish or bead blast to remove the gassing from the texture.”

Nick Tatarchuck

Tool Manager, Ess Tec, Inc.